SHIELDED BADGE HOLDERS

The patent pending Secure Badgeholder™ is a durable, rigid plastic card holder designed to protect a single contactless PIV, CAC, or identification card. The Secure Badgeholder is a barrier to the radio frequency signals that are necessary to communicate with smart cards. This offers protection against unauthorized access to valuable information. With no need to remove the contactless smartcard, the card is read when the user opens the holder by squeezing the tabs. Information is protected when the holder is closed. The Secure Badgeholder meets the requirement of FIPS 201 section 2.6 (PIV Privacy Requirements) and 6.6.2. (Biometric Data Representation and Protection) for an electromagnetically opaque sleeve. Shields ISA 14443/15693 and EPC Gen1/Gen2 contactless smart cards. ******* ITEM IS HEAVY AND WILL REQUIRE ADDITION FREIGHT CHARGES ******* Call for more information or to order custom printing for the back!

BACK TO TOP

MILKY, SEMI-RIGID, MULTI-CARD/MULTI-HANG HOLDERS

Milky White Molded Semi Rigid Plastic Card Holder - Badge strap attachment on horizontal AND vertical sides! Can be used BOTH WAYS! So even if your company has ID cards in both formats, you only need to buy ONE holder! This holder holds 1 to 5 30 mil cards!!!! Credit Card Max. Card: 2 1/8 x 3 3/8" (54 x 86). Outside Dimensions of holder: 2 1/4 W x 3 1/2" H (57 x 89mm)

BACK TO TOP

EASY-ACCESS CARD HOLDERS - HALF-HOLDERS

Easy Access Card Holder, "HALF HOLDER", Hard plastic, Horizontal, designed to be used with PVC cards that need the bottom of the card exposed to swipe bar code or mag stripes. Dimensions are 3.5"x1.5" and each has chain holes and a slot punch molded in for use with any accessory! Center slot and two holes accommodate badge reels, strap clips, plastic neck cords, neck chains and other attachments.

Click on the picture to the right to see a pop-up view
of the Easy-Access "Half Holder" Card Holder

Features & Benefits:

• Convenient: Swipe mag stripe card without removing card from holder
• Secure: Designed to grab and hold card securely
• Versatile: Two die-cut types accommodate a variety of attachments including Strap clips, Badge Reels, Lanyards and more.

BACK TO TOP

HARD PLASTIC ACCESS CARD HOLDERS

This item is frosted/non-glare Hard Plastic. Each piece comes with Slot and chain holes at top. Either format holds a standard prox card, CR80 size card. Both formats are side loaded. Badge is security held in place by a pressure point within the holder itself. Badge can be removed from holder by using the open thumb notch on the back of each holder. Card holding area measures approximately 3-1/2" X 2-1/8". Perfect for protecting those expensive prox cards, yet giving you access to them!

BACK TO TOP

MULTI-CARD, HARD PLASTIC ACCESS CARD HOLDERS

These card holders are frosted, molded, hard plastic, CC sized. They can hold one 30 mil card on the outside, and two 30 mil cards on the inside. Slot and chain holes exist for use with any neck wear. The outside dimensions are 2-3/8" X 4-1/4"

Horizontal holder is TOP LOAD. Vertical holder is SIDE LOAD.

Several colors are available, but are not stocked: black, blue, green, red, yellow, and white

Please note: since these are not stocked, there will be a few days delay in shipping.

BACK TO TOP

VINYL BADGE HOLDERS

Avant's Clear Vinyl Badge Holders provide rugged protection for all your ID credential needs. These versatile holders can be top or side loaded in both vertical or horizontal styles. They can be used with a variety of attachments including: badge clips, bar pins, strap clips, combination clips as well as neck chains, lanyards, and cords. This item has a cut-out on one side, as a thumb tab, so badge can be removed, even after attached to clip or lanyard. IBM/Credit card size measures approximately 2-1/2" X 3-7/8". Military size measures approximately 3-1/8" X 4-1/16" (Vertical) and 3-1/2" X 4-1/4" (Horizontal). Maximum insert card size for Military size is 2-5/8" X 3-7/8".

BACK TO TOP

Colored Badge Holders

Add color to your ID badge with Avant's colored badge holders, which come in a choice of nine colors of durable, protective vinyl. Accent the clear vinyl front panel using color as a solid back, as a bar along the top, or as a picture frame with a clear back panel. Available in one vertical and three horizontal designs, they come with pre-punched holes so they can be worn strap clips, chains, lanyards, coils, or over a button. Maximum ID is Data/Credit Card size (2 21/64" x 3 3/8" 59 x 86mm). Badge can be removed, even after attached to clip or lanyard. IBM/Credit card size measures approximately 2-1/2" X 3-7/8". Military size measures approximately 3-1/8" X 4-5/8".

BACK TO TOP

Magnetic Badge Holders

To avoid damage to clothing, Avant's Magnetic Badge Holders feature two magnets. One is sealed into the front portion of the holder and one in the back. Most often attached to a breast pocket or around a belt, Magnetic Badge Holders are versatile, popular, durable, and extremely professional in appearance. This item has a cut-out on one side, as a thumb tab, so badge can be removed. IBM/Credit card size measures approximately 2-1/2" X 3-7/8".

BACK TO TOP

Arm Bands

Many active situations require prominently displayed ID badges while maintaining a safe working environment. Using a clear vinyl Arm Band Badge Holder is the perfect solution for assembly lines, warehouses, outdoor occupations, construction sites, recreational facilities, airports, and many other specialized work environments. Avant's rugged New and Improved Arm Band Badge Holder is durable and provides trouble-free wear with instant visibility.

BACK TO TOP

SELF-LOCKING PROXIMITY CARD HOLDERS

Proximity Cards require special care and treatment because of the high-tech nature of their design and their cost-per-card. Avant's Self-Locking Clear vinyl Proximity Card badge Holders provide both protection and functionality. When used with strap clips or other strap attachments, the strap/clip threads through the FRONT AND BACK FLAP of the opening, effectively "locking" the card into the holder. IBM/Credit card size measures approximately 2-1/2" X 3-7/8".

BACK TO TOP